===================================================
Geometric Dimensioning and Tolerance [GD&T] Symbols
===================================================

GD&T symbols are typically used by the manufacturing industry to delineate features of a drawing. |HPSNOW| supports the symbols shown in the table below. More information on inserting GD&T symbols can be found in :ref:`this section <prog_guide/0203_text:Using GD&T symbols>` of the programming guide.

**A list of supported GD&T symbols supported in ts3d font and their associated unicode hex values.**

.. csv-table::
	:header: "Symbol", "Unicode hex value", "GD&T symbol name"
	
	.. image:: images/gdt/gdt_2194.png, "0x2194", "Between"
	.. image:: images/gdt/gdt_2197.png, "0x2197", "Circular runout"
	.. image:: images/gdt/gdt_21A7.png, "0x21A7", "Depth/Deep"
	.. image:: images/gdt/gdt_2220.png, "0x2220", "Angularity"
	.. image:: images/gdt/gdt_2225.png, "0x2225", "Parallelism"
	.. image:: images/gdt/gdt_2300.png, "0x2300", "Diameter"
	.. image:: images/gdt/gdt_2312.png, "0x2312", "Profile of a line"
	.. image:: images/gdt/gdt_2313.png, "0x2313", "Profile of a surface"
	.. image:: images/gdt/gdt_2316.png, "0x2316", "Position"
	.. image:: images/gdt/gdt_2322.png, "0x2322", "Arc length"
	.. image:: images/gdt/gdt_232D.png, "0x232D", "Cylindricity"
	.. image:: images/gdt/gdt_232F.png, "0x232F", "Symmetry"
	.. image:: images/gdt/gdt_2330.png, "0x2330", "Total runout"
	.. image:: images/gdt/gdt_2332.png, "0x2332", "Conical taper"
	.. image:: images/gdt/gdt_2333.png, "0x2333", "Slope"
	.. image:: images/gdt/gdt_2334.png, "0x2334", "Counterbore"
	.. image:: images/gdt/gdt_2335.png, "0x2335", "Countersink"
	.. image:: images/gdt/gdt_23E4.png, "0x23E4", "Straightness"
	.. image:: images/gdt/gdt_23E5.png, "0x23E5", "Flatness"
	.. image:: images/gdt/gdt_24BB.png, "0x24BB", "Free state variations"
	.. image:: images/gdt/gdt_24C1.png, "0x24C1", "Least material condition"
	.. image:: images/gdt/gdt_24C2.png, "0x24C2", "Maximum material condition"
	.. image:: images/gdt/gdt_24C5.png, "0x24C5", "Projected tolerance zone"
	.. image:: images/gdt/gdt_24C8.png, "0x24C8", "Regardless of feature size"
	.. image:: images/gdt/gdt_24C9.png, "0x24C9", "Tangent plane"
	.. image:: images/gdt/gdt_24CA.png, "0x24CA", "Unilateral"
	.. image:: images/gdt/gdt_25A1.png, "0x25A1", "Square"
	.. image:: images/gdt/gdt_25CE.png, "0x25CE", "Concentricity"
	.. image:: images/gdt/gdt_25EF.png, "0x25EF", "Circularity"
	.. image:: images/gdt/gdt_27C2.png, "0x27C2", "Perpendicularity"
	.. image:: images/gdt/gdt_E400.png, "0xE400", "Statistical tolerance"
	.. image:: images/gdt/gdt_E401.png, "0xE401", "Third angle projection"
	


Other Supported Symbols
=======================

**A list of other supported symbols in ts3d font and their associated unicode hex values.**

.. csv-table::
	:header: "Symbol", "Unicode hex value", "Character name"
	
	.. image:: images/gdt/gdt_2192.png, "0x2192", ""
	.. image:: images/gdt/gdt_2295.png, "0x2295", "circled plus"
	.. image:: images/gdt/gdt_2296.png, "0x2296", "cirlced minus"
	.. image:: images/gdt/gdt_2302.png, "0x2302", ""
	.. image:: images/gdt/gdt_2323.png, "0x2302", ""
	.. image:: images/gdt/gdt_24BA.png, "0x24BA", ""
	.. image:: images/gdt/gdt_24C7.png, "0x24C7", ""
	.. image:: images/gdt/gdt_25B3.png, "0x25B3", ""
	.. image:: images/gdt/gdt_25CA.png, "0x25CA", ""
	.. image:: images/gdt/gdt_25CB.png, "0x25CB", "white circle"
	.. image:: images/gdt/gdt_E402.png, "0xE402", ""
